how do you hold down your bracelets??? plaesee awswer meeee!!!! page 4
Reply
|
isa-knots2
Professional
 |
4 years, 5 months ago by isa-knots2
i always use a clipboard,, but sometimes ill safety pin it to my pants or backpack if im in a pinch
|
|
KaNoodle
Bracelet King
 |
4 years, 5 months ago by KaNoodle
I own a clipboard and so what I do is I..1. Add tape to the clip part so it doesn’t cut through my string. 2. I then slide the ends/starts of the string under the clipboard clip. 3. I do not slide the full end/start of the string underneath the clip because I then use (I don’t remember the name) some yellow-ish tape (found in a big roll) on the part above the start of the actual bracelet this is just so I have a bit more sturdiness. Hope this helps! 😊 |
|
noemi7
Bracelet King
 |
4 years, 5 months ago by noemi7
@lina999 you can use tape,clipboard or pin it down somewhere (jeans ,pillow , blanket or anything like that)
|
|
noraballet
Professional
 |
4 years, 5 months ago by noraballet
Hydroflask!
|
|
graciebr5
Advanced
 |
4 years, 5 months ago by graciebr5
Clipboard, tape, or safety pin
|
|
RyGyV
Bracelet King
 |
4 years, 5 months ago by RyGyV
I use a clipboard and i tape down the loop then i clip it down.And i also tape it down as i go whenever it gets too hard to knot. Hopefully this helps. 😊 |
|
kmstahl
Bracelet King
 |
4 years, 5 months ago by kmstahl
I use a clip board and I clip a safety pin to the clip board and then if I mess up I just un-clip the safety pin from the clip board and undo the knot with the safety pin.
|
|
ks_wizard
Bracelet King
 |
4 years, 5 months ago by ks_wizard
i use a clipboard, since tape normally i feel is wasteful, and the string doesn't hold the best. i do use tape for alphas
|
|
MacKenzie7
Professional
 |
4 years, 5 months ago by MacKenzie7
I use safety pins and tape most of the time
|
|
Magic28
Bracelet King
 |
4 years, 5 months ago by Magic28
I usually use a clipboard, sometimes I use tape!
|
|
emordnilap
Professional
 |
4 years, 5 months ago by emordnilap
I use a clipboard, but when I'm at my desk I use tape. I like being able to sit where I want, but triangle ends I have to do at my desk.
|
|
jadeflwr13
Bracelet King
 |
4 years, 5 months ago by jadeflwr13
i prefer using a mason jar. i just screw the lid on over the strings then start knotting! i find that the strings under the lid don’t move around too 🌸✨
|
|
dray
Professional
 |
4 years, 5 months ago by dray
It really depends where I am. Most of the time I use a clipboard. If I am at summer camp I use tape. If I can’t find either of those I tie a loop and use my big toe. 😂
|
|
beachyknot
Professional
 |
4 years, 5 months ago by beachyknot
I use a clipboard and then as the bracelet grows either move it further up the clipboard or tape it down!
|
|
lindseylou
Advanced
 |
4 years, 5 months ago by lindseylou
I like to put mine on a water bottle or a binder clip
|
|
-Dominika-
Skiller
 |
4 years, 5 months ago by -Dominika-
I use a binder clip on the edge of a book, then as the bracelet gets longer, i fold it over the back and re-clip it 😉
|
|
JuliaW9
Bracelet King
 |
4 years, 5 months ago by JuliaW9
I use a clipboard and sometimes tape.
|
|
ilovemasha
Professional
 |
4 years, 5 months ago by ilovemasha
I use a binder clip and a binder!!
|
|
CoolKnot
Bracelet King
 |
4 years, 5 months ago by CoolKnot
I wouldn’t recommend using tape because you will go through it really quickly, and I generally use a clipboard. I sometimes like to use binder clips or safety pins, and safety pins are one of my favourites because you can pin them anywhere and it doesn’t take much space
|
|
normando
Advanced
 |
4 years, 5 months ago by normando
I recommend using a binder and cutting off the top flap, you then put the loop in one of the rings
|
