What so you use to hold your work
Reply
|
acidburn
Advanced
 |
3 years, 6 months ago by acidburn
I use a clipboard but it doesn't grip that hard it slides as I'm knotting
|
|
n3sela
Skiller
 |
3 years, 6 months ago by n3sela
i use tape or even a binder clip, binder clips work really well tho
|
|
halokiwi
Moderator
 |
3 years, 6 months ago by halokiwi
I use a combination of tape and clipboard. You can use the advantages of both that way.
|
|
acidburn
Advanced
|
3 years, 6 months ago by acidburn
So using clipboard and tape you would clip the top and tape the lower work until finished
|
|
Karo-H
Bracelet King
 |
3 years, 6 months ago by Karo-H
I also use the tape/clipboard combinationI use the clipboard to hold the beginning, yet I do secure it with some tape as well, just in case. Once you have some inches made of your bracelet I secure the bracelet once more with tape to the clipboard, to make sure it doesn't move all that much. important note: make sure your tape isn't the kind to stick to your bracelet (as in when you pull it off it takes parts of it with the tape so it gives your bracelet this "worn" look) OR leaves a sticky residue on your creation! |
|
Horse_Shoe
Bracelet King
 |
3 years, 6 months ago by Horse_Shoe
I use tape a clipbourd and for small normals I will use a safety pin
|
|
RangerLane
Bracelet King
 |
3 years, 6 months ago by RangerLane
I use a clipboard, but i tie a knot at the top first and it holds pretty well. For alphas i use duck tape.
|
|
Milo2dog
Professional
 |
3 years, 6 months ago by Milo2dog
I use a foldback clip and clip it to a book!
|
|
minutcraft
Bracelet King
 |
3 years, 6 months ago by minutcraft
I use a butterfly board clip and a hard surface that's similar to a wooden clip board (because I don't like the gaps that tend to exist along the contact point of most clipboard clips and bull-clips). It also makes it possible for me to just replace the clip whenever it gets too loose with a new one instead of buying a whole new clipboard.
|
|
Birte
Professional
 |
3 years, 6 months ago by Birte
i just tape it to my table or a clipbord with tape
|
|
stormii
Bracelet King
 |
3 years, 6 months ago by stormii
some people use tape, I don't because I usually knot too hard and the tape comes off every 5 seconds. you can also use a binder clip clipped to a notebook, or a clipboard, I use both of these and they work pretty well. when I'm making my beginning loop, there's nothing for the binder or clipboard to hold on to, so I tape the strings down, and then once I have my beginning loop done, I switch to a clip. If you're using a clipboard or binder clip, you'll notice as the bracelet gets longer and the end is farther away from the clip, it will be harder to make the knots. once it gets to this point, you can either tape down part of the bracelet close to where you are working, or move the bracelet up and maneuver the clip so it is on the bracelet close to where you are working. hope this helps 🙂
|
|
stasia
Bracelet King
 |
3 years, 6 months ago by stasia
Tape tape tape tape!!! I fix it to a mobile desk which i work on ❤️❤️
|
|
ChloeZ
Skiller
 |
3 years, 6 months ago by ChloeZ
Sometimes I tape it to a table or I use a clipboard
|
|
Blueknot
Bracelet King
 |
3 years, 6 months ago by Blueknot
I put mine in the box that I have my string in. Then at some point I got a box that is the same thing just smaller and it goes with me everywhere. Even just to the groceery store. Kinda like my security blanket. 😂
|
|
strings28
Bracelet King
 |
3 years, 6 months ago by strings28
Tape and a clipboard. Masha knot
|
|
strings28
Bracelet King
|
3 years, 6 months ago by strings28
Uses a clipboard.
|
|
strings28
Bracelet King
|
3 years, 6 months ago by strings28
Oops, a safety pin.
|
|
Panbylee
Professional
 |
3 years, 5 months ago by Panbylee
I use a little clipboard. It's one of the more old fashioned looking ones where the clip is more like a big binder clip. I don't like tape because I feel like it makes the string more fuzzy.
|
|
gnvbooks
Professional
 |
3 years, 5 months ago by gnvbooks
I use a safety pin
|
